Коды неисправностей телескопа JCB - Автозапчасти и автоХитрости

Автозапчасти и автоХитрости
Автозапчасти и автоХитрости
Автозапчасти и автоХитрости
Подписывайтесь на наш канал в Telegram и будьте всегда в курсе самых последних сообщений и публикаций с сайта.
Перейти к контенту
 См. также:
Коды неисправностей телескопического погрузчика JCB

Dashboard
D000 Ambient temperature sensor fault (550-80)
D001 Air Filter Blocked
D002 Water In Fuel Detected
D003 Water in fuel operator fault
D004 Coolant Over Temperature
D006 Transmission Temperature Over Heat
D010 Coolant Level Low
D011 Engine Oil Low When Engine Started
D012 Engine Oil Pressure Low
D014 Transmission Pressure Low
D079 CAN Communications Fault
D106 Alternator Excitation Open Circuit
D107 Engine RPM Open Circuit
D108 Ground Speed Open Circuit
D115 Transmission Pressure Output Open
D117 Fuel Level Sensor Open
D118 Coolant Temperature Sensor Open
D119 Water In Fuel Sensor Open Circuit
D128 Reversing Fan Output Open Circuit
D205 Alternator Not Charging
D215 Transmission Pressure Output Short
D217 Fuel level Sensor Short
D218 Coolant Temperature Sensor Short
D219 Water In Fuel Sensor Short Circuit
D228 Reversing Fan Output Short Circuit
D231 Brake Pressure Transducer Out of Range
D300 CAN Communications Fault

Engine
E001 Engine Control Module Data erratic, intermittent or incorrect
E001 Engine Control Module Root cause not known
E001 Engine Control Module Bad intelligent device or component
E001 Engine Control Module Condition exists
E002 Engine Speed Sensor Data erratic, intermittent or incorrect
E004 Fuel Timing Pressure Sensor Circuit Voltage below normal or shorted to low source
E008 Intake Manifold Pressure Sensor Fault Voltage above normal or shorted to high source
E009 Intake Manifold Pressure Sensor Fault Voltage below normal or shorted to low source
E010 Accelerator pedal position Voltage above normal or shorted to high source
E011 Accelerator pedal position Voltage below normal or shorted to low source
E012 Hand Throttle Position Sensor Fault Voltage above normal or shorted to high source
E013 Hand Throttle Position Sensor Fault Voltage below normal or shorted to low source
E014 Engine Oil Pressure Voltage above normal or shorted to high source
E015 Engine Oil Pressure Voltage below normal or shorted to low source
E017 Engine Coolant Temperature Voltage above normal or shorted to high source
E018 Engine Coolant Temperature Voltage below normal or shorted to low source
E023 Intake Manifold Temperature Sensor Fault Voltage above normal or shorted to high source
E024 Intake Manifold Temperature Sensor Fault Voltage below normal or shorted to low source
E027 Sensor Supply Voltage Circuit Voltage below normal or shorted to low source
E027 Sensor Supply Voltage 3 (+5V) Voltage above normal or shorted to high source
E036 Sensor Supply Voltage 3 (+5V) Data erratic, intermittent or incorrect
E040 Vehicle Speed Sensor Fault Data erratic, intermittent or incorrect
E041 Vehicle Speed Sensor Circuit Data abnormal rate of change
E047 Fuel Temperature Voltage above normal or shorted to high source
E048 Fuel Temperature Root cause not known
E049 Fuel Temperature Voltage below normal or shorted to low source
E051 High Fuel Pressure Solenoid Valve Number 1 Fault Voltage below normal, or shorted to low source
E052 High Fuel Pressure Solenoid Valve Number 1 Fault Voltage above normal, or shorted to high source
E052 High Fuel Pressure Solenoid Valve Number 1 Fault Current below normal or open circuit
E055 High Fuel Pressure Solenoid Valve Number 1 Fault Mechanical system not responding or out of adjustment
E068 Engine Control Module Temperature Sensor Voltage above normal, or shorted to high source
E069 Engine Control Module Temperature Sensor Voltage below normal, or shorted to low source
E076 Injector Solenoid Valve Cylinder # 1 Current above normal or grounded circuit
E078 Injector Solenoid Valve Cylinder # 3 Current above normal or grounded circuit
E080 Injector Solenoid Valve Cylinder # 2 Current above normal or grounded circuit
E082 Injector Solenoid Valve Cylinder # 4 Current above normal or grounded circuit
E083 Injector Solenoid Valve Cylinder Number 1 Fault Current below normal or open circuit
E085 Injector Solenoid Valve Cylinder Number 3 Fault Current below normal or open circuit
E089 Injector Solenoid Valve Cylinder Number 2 Fault Current below normal or open circuit
E090 Injector Solenoid Valve Cylinder Number 4 Fault Current below normal or open circuit
E091 Calibration Memory Data erratic, intermittent or incorrect
E091 Calibration Memory Condition exists
E095 Sensor Supply Voltage 1 (+5V) Voltage below normal, or shorted to low source
E096 Engine Fuel Injection Pump Fuel Control Valve (IMV) Voltage above normal, or shorted to high source
E097 Engine Fuel Injection Pump Fuel Control Valve (IMV) Voltage below normal, or shorted to low source
E098 Fuel Pump Control Module, CAN Mechanical system not responding or out of adjustment
E104 Fuel Pump Control Module, Idle Data erratic, intermittent or incorrect
E113 Sensor Supply Voltage 2 Voltage above normal or shorted to high source
E114 Sensor Supply Voltage 1 (+5V) Voltage above normal, or shorted to high source
E119 Water in Fuel Indicator Data valid but above normal operating range - least severe level
E122 Water in Fuel Indicator Fault Voltage above normal or shorted to high source
E123 Water in Fuel Indicator Fault Voltage below normal or shorted to low source
E126 Intake Manifold Pressure Sensor Fault Data erratic, intermittent or incorrect
E127 Power Supply Fault Data erratic, intermittent or incorrect
E129 Battery Voltage Fault Data valid but below normal operational range - most severe level
E130 Battery Voltage Fault Data valid but above normal operational range - most severe level
E133 Fuel pump delivery pressure Data valid but above normal operating range - moderately severe level
E134 Injector Metering Rail # 1 Pressure Voltage above normal or shorted to high source
E135 Injector Metering Rail Pressure Fault Voltage below normal or shorted to low source
E159 Cylinder Power Imbalance between cylinders Data erratic, intermittent or incorrect
E172 Engine Coolant Temperature Data erratic, intermittent or incorrect
E183 Injector Metering Rail # 1 Pressure Data erratic, intermittent or incorrect
E202 Minimum drive pulse drift (inj #2) Mechanical system not responding or out of adjustment
E203 Minimum drive pulse drift (inj #1) Mechanical system not responding or out of adjustment
E204 Minimum drive pulse drift (inj #3) Mechanical system not responding or out of adjustment
E205 Minimum drive pulse drift (inj #0) Mechanical system not responding or out of adjustment
E700 Fuel pump delivery pressure Data valid but below normal operational range - most severe level
E701 High Fuel Pressure Solenoid Valve Number 1 Fault Data erratic, intermittent or incorrect
E701 High Fuel Pressure Solenoid Valve Number 1 Fault Data erratic, intermittent or incorrect
E702 Fuel pump delivery pressure Data valid but below normal operating range - least severe level
E703 Fuel pump delivery pressure Condition exists
E704 Engine Knock Sensor Abnormal frequency or pulse width or period
E704 Engine Knock Sensor Condition exists
E708 Engine Control Module Main Relay Mechanical system not responding or out of adjustment
E709 Engine Coolant Temperature Condition exists
E710 Intake Air Heater (Relay Enable) # 1 Voltage above normal or shorted to high source
E711 Intake Air Heater (Relay Enable) # 1 Voltage below normal or shorted to low source
E712 Intake Air Heater (Relay Enable) # 1 Current below normal or open circuit
E713 Intake Air Heater (Relay Enable) # 1 Current above normal or grounded circuit
E714 Cruise Control Set Speed Mechanical system not responding or out of adjustment
E715 Boost pressure plausibility Condition exists
E716 Accelerator pedal position Data erratic, intermittent or incorrect
E717 Injector Metering Rail # 1 Pressure Condition exists
E718 Engine position sensor Data erratic, intermittent or incorrect
E719 Engine Speed Sensor Data erratic, intermittent or incorrect
E720 Engine Speed Sensor Abnormal rate of change
E722 Auxiliary Output #1 (Temperature Gauge / Lamp) Voltage below normal or shorted to low source
E723 Auxiliary Output #1 (Temperature Gauge / Lamp) Current below normal or open circuit
E724 Auxiliary Output #1 (Temperature Gauge / Lamp) Current above normal or grounded circuit
E725 Wiring harness resistance too high/low (cyl #4) Abnormal rate of change
E726 Wiring harness resistance too high/low (cyl #2) Abnormal rate of change
E727 Wiring harness resistance too high/low (cyl #1) Abnormal rate of change
E728 Wiring harness resistance too high/low (cyl #3) Abnormal rate of change
E729 Engine Injector Bank 1 Voltage above normal, or shorted to high source
E730 Engine Injector Bank 2 Voltage above normal, or shorted to high source
E731 High Fuel Pressure Solenoid Valve Number 1 Fault Data valid but above normal operational range - most severe level
E732 High Fuel Pressure Solenoid Valve Number 1 Fault Data valid but below normal operational range - most severe level
E733 Maintenance Lamp Voltage below normal, or shorted to low source
E734 Maintenance Lamp Current below normal or open circuit
E735 Maintenance Lamp Current above normal or grounded circuit
E736 Engine Injector Bank 1 Voltage below normal, or shorted to low source
E737 Engine Knock Sensor Root cause not known
E737 Engine Injector Bank 2 Voltage below normal, or shorted to low source
E738 Hand Throttle Position Sensor Fault Data erratic, intermittent or incorrect
E746 Auxiliary Output #2 (Oil Pressure Gauge / Lamp)) Voltage below normal or shorted to low source
E747 Engine Gaseous Fuel Correction Factor Out of calibration
E748 Engine Gaseous Fuel Correction Factor Data erratic, intermittent or incorrect
E749 Auxiliary Output #2 (Oil Pressure Gauge / Lamp)) Current below normal or open circuit
E750 Auxiliary Output #2 (Oil Pressure Gauge / Lamp)) Current above normal or grounded circuit
E751 Malfunction Indicator Lamp Voltage above normal, or shorted to high source
E752 Maintenance Lamp Voltage above normal, or shorted to high source
E753 Engine Electric Lift Pump for Engine Fuel Supply Voltage above normal or shorted to high source
E755 Engine position sensor Mechanical system not responding or out of adjustment
E756 Vehicle Speed Sensor Fault Voltage below normal or shorted to low source
E757 ECU Power Output Supply #2 Current below normal or open circuit
E758 ECU Power Output Supply #2 Current above normal or grounded circuit
E759 Engine Speed Sensor Mechanical system not responding or out of adjustment
E760 Engine Electric Lift Pump for Engine Fuel Supply Voltage below normal or shorted to low source
E761 Engine Electric Lift Pump for Engine Fuel Supply Current below normal or open circuit
E762 Engine Electric Lift Pump for Engine Fuel Supply Current above normal or grounded circuit
E763 Intake Manifold Temperature Sensor Fault Condition exists
E773 Malfunction Indicator Lamp Current above normal or grounded circuit
E774 Injector Metering Rail # 1 Pressure Out of calibration
E775 Sensor Supply Voltage 1 (+5V) Data erratic, intermittent or incorrect
E776 Engine Fuel Injection Pump Fuel Control Valve (IMV) Current below normal or open circuit
E777 Engine Fuel Injection Pump Fuel Control Valve (IMV) Current above normal or grounded circuit
E778 Engine Fuel Injection Pump Fuel Control Valve (IMV) Data valid but above normal operating range - moderately severe level
E779 Engine Fuel Injection Pump Fuel Control Valve (IMV) Data valid but below normal operating range - least severe level
E780 Engine Fuel Injection Pump Fuel Control Valve (IMV) Condition exists
E781 Sensor Supply Voltage 3 (+5V) Data erratic, intermittent or incorrect
E782 Malfunction Indicator Lamp Voltage below normal, or shorted to low source
E783 Malfunction Indicator Lamp Current below normal or open circuit
E784 Intake Manifold Temperature Sensor Fault Abnormal rate of change
E785 Vehicle Speed Sensor Fault Current below normal or open circuit
E786 Intake Air Heater (Relay Enable) # 2 Voltage below normal or shorted to low source
E787 Intake Air Heater (Relay Enable) # 2 Current below normal or open circuit
E788 Intake Air Heater (Relay Enable) # 2 Current above normal or grounded circuit
E789 Vehicle Speed Sensor Fault Current above normal or grounded circuit
E790 Vehicle Speed Sensor Fault Mechanical system not responding or out of adjustment
E791 Vehicle Speed Sensor Fault Voltage above normal or shorted to high source
E792 Auxiliary Output #1 (Temperature Gauge / Lamp) Voltage above normal or shorted to high source
E793 Auxiliary Output #2 (Oil Pressure Gauge / Lamp)) Voltage above normal or shorted to high source
E794 Intake Air Heater (Relay Enable) # 2 Voltage above normal or shorted to high source
E795 Sensor Supply Voltage 2 Data erratic, intermittent or incorrect
E796 ECU Power Output Supply #2 Voltage below normal or shorted to low source
E797 ECU Power Output Supply #1 Voltage below normal or shorted to low source
E798 ECU Power Output Supply #1 Current below normal or open circuit
E799 ECU Power Output Supply #1 Current above normal or grounded circuit Hydraulics

Hydraulics
L000 10 degree prox switch open
L001 10 degree prox switch short
L002 10 degree switch power open
L003 10 degree switch power STG
L004 10 degree switch power STB
L005 boom retracted switch open
L006 boom retracted switch short
L007 boom retracted switch power open
L008 boom retracted switch power STG
L009 boom retracted switch power STB
L010 45 degree prox switch open
L011 45 degree prox switch short
L012 45 degree switch power open
L013 45 degree switch power STG
L014 45 degree switch power STB
L015 Lower Switch OORL
L016 Lower Switch OORH
L017 Tilt Switch OORL
L018 Tilt Switch OORH
L019 Lower / Tilt Switch Power Open
L020 Lower / Tilt Switch Power STG
L021 Lower / Tilt Switch Power STB
L022 Load Management Indicator Fault
L023 SRS switch Short
L024 80% Solenoid Open
L025 80% Solenoid STG
L026 80% Solenoid STB
L027 100% Solenoid Open
L028 100% Solenoid STG
L029 100% Solenoid STB
L030 Accumulator Solenoid Open
L031 Accumulator Solenoid STG
L032 Accumulator Solenoid STB
L033 Drain Solenoid Open
L034 Drain Solenoid STG
L035 Drain Solenoid STB
L036 Extend Solenoid Open
L037 Extend Solenoid STG
L038 Extend Solenoid STB
L039 Retract Solenoid Open
L040 Retract Solenoid STG
L041 Retract Solenoid STB
L042 Extend/Retract Solenoid Return Open
L043 Extend/Retract Solenoid Return STG
L044 Extend/Retract Solenoid Return STB
L045 Auxiliary A Solenoid Open
L046 Auxiliary A Solenoid STG
L047 Auxiliary A Solenoid STB
L048 Auxiliary B Solenoid Open
L049 Auxiliary B Solenoid STG
L050 Auxiliary B Solenoid STB
L051 Auxiliary A/B Solenoid Return Open
L052 Auxiliary A/B Solenoid Return STG
L053 Auxiliary A/B Solenoid Return STB
L054 Auxiliary Changeover Solenoid Open
L055 Auxiliary Changeover Solenoid STG
L056 Auxiliary Changeover Solenoid STB
L057 Extend / Retract Thumbwheel OORL
L058 Extend / Retract Thumbwheel OORH
L059 Column FNR neutral switch open
L060 Column FNR neutral switch short
L061 Auxiliary Thumbwheel OORL
L062 Auxiliary Thumbwheel OORH
L063 Hydraulic Lock Switch Open
L064 Hydraulic Lock Switch Short
L065 Neutral Start Relay Open
L066 Neutral Start Relay STG
L067 Neutral Start Relay STB
L068 Joystick FNR Switch Power Open
L069 Joystick FNR Switch Power STG
L070 Joystick FNR Switch Power STB
L071 CAN fault
L072 EEPROM Fault
L073 Lower Switch Disagreement
L074 Tilt Switch Disagreement
L075 Boom Angle Sensor Disagreement
L076 Boom Angle Sensor 1 OORL
L077 Boom Angle Sensor 1 OORH
L078 Boom Angle Sensor 2 OORL
L079 Boom Angle Sensor 2 OORH
L080 Lift press Switch OORL
L081 Lift press Switch OORH
L082 raise Solenoid Open
L083 raise Solenoid STG
L084 raise Solenoid STB
L085 lower Solenoid Open
L086 lower Solenoid STG
L087 lower Solenoid STB
L088 crowd Solenoid Open
L089 crowd Solenoid STG
L090 crowd Solenoid STB
L091 dump Solenoid Open
L092 dump Solenoid STG
L093 dump Solenoid STB
L094 throttle extend Open
L095 throttle extend STG
L096 throttle extend STB
L097 throttle retract Open
L098 throttle retract STG
L099 throttle retract STB
L100 throttle LS relay Open
L101 throttle LS relay STG
L102 throttle LS relay STB
L103 hyd isolate solenoid Open
L104 hyd isolate solenoid STG
L105 hyd isolate solenoid STB
L106 raise/lower Solenoid Return Open
L107 raise/lower Solenoid Return STG
L108 raise/lower Solenoid Return STB
L109 crowd/dump Solenoid Return Open
L110 crowd/dump Solenoid Return STG
L111 crowd/dump Solenoid Return STB
L112 tilt lock switch open
L113 tilt lock switch short
L114 Throttle Position Feedback OORL
L115 Throttle Position Feedback OORH
L116 SRS pressure switch OORL
L117 SRS pressure switch OORH
L118 SRS pressure switch disagreement
L119 Throttle Dial Sensor 1 OORL
L120 Throttle Dial Sensor 1 OORH
L121 Throttle Dial Sensor 2 OORL
L122 Throttle Dial Sensor 2 OORH
L123 Throttle Dial Disagreement
L124 Boom movement when joystick is neutral (stuck spool)
L125 Boom movement when LMI is > 115%
L126 Throttle not able to achieve position
L127 emergency stop switch short
L128 emergency stop switch open
L129 speed sensor OORH
L130 speed sensor OORL
L131 speed sensor disagreement
L132 Chassis Angle Sensor Disagreement
L133 Chassis Angle Sensor 1 OORL
L134 Chassis Angle Sensor 1 OORH
L135 Chassis Angle Sensor 2 OORL
L136 Chassis Angle Sensor 2 OORH
L137 Sway Switch Open
L138 Sway Switch Short
L139 Stabilizer Isolation Switch Open
L140 Stabilizer Isolation Switch Short
L141 Lift / Lower Spool Neutral disagreement
L142 Lift / Lower Spool OORL
L143 Lift / Lower Spool OORH
L144 Ext / Retract Spool Neutral disagreement
L145 Ext / Retract Spool OORL
L146 Ext / Retract Spool OORH
L147 Crowd / Dump Spool Neutral disagreement
L148 Crowd / Dump Spool OORL
L149 Crowd / Dump Spool OORH
L150 Aux A/B Spool Neutral disagreement
L151 Aux A/B Spool OORL
L152 Aux A/B Spool OORH
L153 Left Stabilizer Spool Neutral disagreement
L154 Left Stabilizer Spool OORL
L155 Left Stabilizer Spool OORH
L156 Right Stabilizer Spool Neutral disagreement
L157 Right Stabilizer Spool OORL
L158 Right Stabilizer Spool OORH
L159 Ext_Aux2B_sw_OOR
L160 AuxA_AuxB_sw_OOR
L161 Ret_Aux2A_sw_OOR
L162 sway isolation Solenoid Open
L163 sway isolation Solenoid STG
L164 sway isolation Solenoid STB
L165 Switch Supply Open
L166 Switch Supply STG
L167 Switch Supply STB
L168 Transmission dump OPEN
L169 Transmission dump STG
L170 Transmission dump STB
L171 STAB isolation Solenoid Open
L172 STAB isolation Solenoid STG
L173 STAB isolation Solenoid STB
L174 Sway Right Solenoid Open
L175 Sway Right Solenoid STG
L176 Sway Right Solenoid STB
L177 Sway LEFT Solenoid Open
L178 Sway LEFT Solenoid STG
L179 Sway LEFT Solenoid STB
L180 Sway / Stab Isolation return relay Open
L181 Sway / Stab Isolation return relay STG
L182 Sway / Stab Isolation return relay STB
L183 motion cut valve LS open
L184 motion cut valve LS short to batt
L185 engine start with immobilizer on
L186 left stabilizer deployed sensor disagreement
L187 right stabilizer deployed sensor disagreement

Man Platform
M000 Critical fault received by the EHC.
M001 Loss of CAN communication with the EHC.
M002 Loss of CAN communication with the manbasket radio.
M005 Loss of Can communication with the LMI
M006 Sway left output short to BAT
M007 Sway left output short to GND
M008 Sway left output open-circuit
M009 Sway right output short to BAT
M010 Sway right output short to GND
M011 Sway right output open-circuit
M012 Sway isolate output short to BAT
M013 Sway isolate output short to GND
M014 Sway isolate output open-circuit
M015 Emergency boom lower output short to BAT
M016 Emergency boom lower output short to GND
M017 Emergency boom lower output open-circuited
M018 Emergency boom retract output short to BAT
M019 Emergency boom retract output short to GND
M020 Emergency boom retract output open-circuited
M021 Manbasket mode active output (to EHC) short to BAT
M022 Manbasket mode active output (to EHC) short to GND
M023 Manbasket mode active output (to EHC) open-circuited
M024 LH stabilizer lower output short to BAT
M025 LH stabilizer lower output short to GND
M026 LH stabilizer lower output open-circuited
M027 LH stabilizer raise output short to BAT
M028 LH stabilizer raise output short to GND
M029 LH stabilizer raise output open-circuited
M030 RH stabilizer lower output short to BAT
M031 RH stabilizer lower output short to GND
M032 RH stabilizer lower output open-circuited
M033 RH stabilizer raise output short to BAT
M034 RH stabilizer raise output short to GND
M035 RH stabilizer raise output open-circuited
M036 Start relay output short to BAT
M037 Start relay output short to GND
M038 Start relay output open-circuited
M039 Emergency recovery pump short to BAT
M040 Emergency recovery pump short to GND
M041 Emergency recovery pump open-circuited
M042 Emergency fourth boom retract output short to BAT
M043 Emergency fourth boom retract output short to GND
M044 Emergency fourth boom retract output open-circuited
M045 Transmission dump output short to BAT
M046 Transmission dump output short to GND
M047 Transmission dump output open-circuited
M048 Alarm output short to BAT
M049 Alarm output short to GND
M050 Alarm output open-circuited
M051 ESOS output short to BAT
M052 ESOS output short to GND
M053 ESOS output open-circuited
M054 Engine ESOS/Crank return short to GND
M055 Engine ESOS/Crank return short to BAT
M056 Engine ESOS/Crank return open-circuited
M057 LH Stabilizer Return output short to GND
M058 LH Stabilizer Return output short to BAT
M059 LH Stabilizer Return output open-circuited
M060 Emergency Boom Return output short to GND
M061 Emergency Boom Return output short to BAT
M062 Emergency Boom Return output open-circuited
M063 RH Stabilizer Return output short to GND
M064 RH Stabilizer Return output short to BAT
M065 RH Stabilizer Return output open-circuited
M066 Park brake NO and NC inputs mismatch
M067 RH stabilizer digital and analog feedback sensors mismatch
M068 LH stabilizer digital and analog feedback sensors mismatch
M069 More than 1 (or none) FNR inputs are active at the same time.
M070 Basket overload inputs mismatch
M071 Emergency recovery button inputs mismatch
M071 Emergency recovery mode entered due to CAN fault
M072 Boom retracted inputs disagreement.
M073 Stabilizer isolated inputs mismatch
M075 Manbasket mode cannot be entered due to missing wire security signal.
M076 Boom emergency stop redundant inputs mismatch
M077 Cab emergency stop redundant inputs mismatch
M078 RH stabilizer lever 1 shorted to BAT
M079 RH stabilizer lever 1 shorted to GND
M080 RH stabilizer lever 2 shorted to BAT
M081 RH stabilizer lever 2 shorted to GND
M082 The RH stab lever redundant signal mismatch
M083 LH stabilizer lever 1 shorted to BAT
M084 LH stabilizer lever 1 shorted to GND
M085 LH stabilizer lever 2 shorted to BAT
M086 LH stabilizer lever 2 shorted to GND
M087 The LH stab lever redundant signal mismatch
M088 RH stabilizer pressure sensor shorted to BAT
M089 RH stabilizer pressure sensor shorted to GND
M090 LH stabilizer pressure sensor shorted to BAT
M091 LH stabilizer pressure sensor shorted to GND
M092 Sway LH redundant input mismatch
M092 Sway RH redundant input mismatch
M092 Both sway left and sway right inputs are on at the same time
M092 Vref voltage out of range high
M093 EHC redundant manbasket confirmation inputs mismatch.
M093 Vref voltage out of range low
M095 Radio RPM increment redundant inputs mismatch
M096 Radio RPM decrement redundant inputs mismatch
M097 Radio throttle mode select redundant inputs mismatch
M098 Radio spare 2 button redundant inputs mismatch
M099 Radio spare 3 button redundant inputs mismatch
M100 Radio spare 4 button redundant inputs mismatch
M101 Application checksum failed.
M102 Constant data checksum failed
M103 Emergency recovery mode entered by pressing the emergency recovery inputs
M104 Emergency recovery mode entered due to park brake being disengaged.
M105 Emergency recovery mode entered due to a fault on one of the RH stabilizer outputs.
M106 Emergency recovery mode entered due to a fault on one of the LH stabilizer outputs.
M107 Emergency recovery mode entered due to FNR no longer in neutral.
M108 Emergency recovery mode entered due to the EHC no longer allowing manbasket mode.
M110 Engine failed to start during cranking.
M111 Radio in cradle inputs disagreement.
M112 Emergency recovery mode entered due to stabilizers no longer deployed.
M113 Emergency recovery mode entered due to radio no longer in the cradle.
M114 Emergency recovery mode entered due to basket overload.
M115 Emergency recovery mode entered due to disagreement with
the radio spare 3 buttons in disagreement (cannot determine
wether to retract 4th extension or main boom)
M116 Emergency recovery mode entered due to loss of wire security signal.
M117 Emergency recovery entered due to instability of vehicle.
M118 Emergency recovery mode entered due to critical fault on the EHC controller.
M119 Emergency recovery mode entered due to a fault on one of the emergency recovery boom outputs.
M120 Emergency recovery mode entered due to a fault on the emergency recovery pumpt output.
M121 Emergency recovery mode entered due to a short to BAT on the starter motor output.
M122 Emergency recovery mode entered due to a fault on one of the sway outputs.
M123 Emergency recovery mode entered due to a fault on the transmission dump output.
M130 Manbasket mode cannot be entered due to park brake not engaged.
M131 Manbasket mode cannot be entered because FNR not in neutral.
M132 Manbasket mode cannot be entered because the stabililzers are not deployed
M133 Manbasket mode cannot be entered due to a fault with one or more the sway inputs.
M134 Manbasket mode cannot be entered due to a fault with one or more of the stabilizer lever inputs.
M135 Manbasket mode cannot be entered due to a fault with the spare 3 redundant inputs.
M136 Manbasket mode cannot be entered due to a fault with one or more of the stabilizer outputs.
M137 Manbasket mode cannot be entered due to a fault with one or more of the sway outputs.
M138 Manbasket mode cannot be entered due to a fault with one or more of the emergency recovery boom outputs.
M139 Manbasket mode cannot be entered due to a fault with the emergency pump output.
M140 Manbasket mode cannot be entered because the boom is too high.
M141 Manbasket mode cannot be entered because the vehicle is unstable.
M142 Manbasket mode cannot be entered due to a fault on the EHC controller.
M143 Manbasket mode cannot be entered due to a CAN fault.
M144 Manbasket mode cannot be entered due to a fault with the transmission dump output.
M145 Manbasket mode cannot be entered due to a fault on the starter output or the ESOS output
M150 The ignition input is in an undefined state.
M151 Cranking input 1 is in an undefined state.
M152 Wire security input is in an undefined state
M153 FNR neutral input is in an undefined state
M154 FNR not neutral input is in an undefined state
M155 Cranking input 2 is in an undefined state
M156 Sway right switch 1 input is in an undefined state
M157 Sway right switch 2 input is in an undefined state
M158 Stabilizer isolation 1 input is in an undefined state
M159 Stabilizer isolation 2 input is in an undefined state
M160 Emergency stop 1 input is in an undefined state
M161 Emergency stop 2 input is in an undefined state
M162 Sway left switch 1 input is in an undefined state
M163 Sway left switch 2 input is in an undefined state
M164 Boom emergency stop 1 input is in an undefined state
M165 Boom emergency stop 2 input is in an undefined state
M166 Joystick key switch input is in an undefined state
M167 Parking brake NO input is in an undefined state
M168 Parking brake NC input is in an undefined state
M169 Basket overload 1 input is in an undefined state
M170 Basket overload 2 input is in an undefed state
M171 Emergency recovery input 1 is in an undefined state
M172 Emergency recovery input 2 is in an undefined state
M173 Boom retracted input 1 is in an undefined state
M174 Boom retracted input 2 is in an undefined state
M200 The vehicle has previously entered manbasket mode.

Transmission         527-58 Only
T000 Column Switch Neutral OOR
T001 Column Switch Forward OOR
T002 Column Switch Reverse OOR
T003 Column Switch Short
T004 Column Switch Open
T005 Joystick FNR Short
T006 Joystick FNR Open
T007 Joystick CAN fault
T008 Joystick FNR Neutral fault
T009 Joystick FNR Forward fault
T010 Joystick FNR Reverse fault
T011 Pump Forward High Side STB
T012 Pump Forward High Side STG
T013 Pump Forward High Side Open
T014 Pump Forward Low Side STB
T015 Pump Forward Low Side STG
T016 Pump Forward Low Side Open
T017 Pump Reverse High Side STB
T018 Pump Reverse High Side STG
T019 Pump Reverse High Side Open
T020 Pump Reverse Low Side STB
T021 Pump Reverse Low Side STG
T022 Pump Reverse Low Side Open
T023 Motor Control High Side STB
T024 Motor Control High Side STG
T025 Motor Control High Side Open
T026 Motor Control Low Side STB
T027 Motor Control Low Side STG
T028 Motor Control Low Side Open
T029 Fast/Slow High Side STB
T030 Fast/Slow High Side STG
T031 Fast/Slow High Side Open
T032 Fast/Slow Low Side STB
T033 Fast/Slow Low Side STG
T034 Fast/Slow Low Side Open
T035 Creep Dial 1 STG
T036 Creep Dial 1 STB
T037 Creep Dial 2 STG
T038 Creep Dial 2 STB
T039 Creep Dial Mismatch
T040 Park Brake Open
T041 Park Brake Short
T042 Transmission Temp Sensor OORL
T746 Transmission Temp Sensor OORH
T044 Steer Valve A STB
T045 Steer Valve A STG
T046 Steer Valve A Open
T047 Steer Valve B STB
T048 Steer Valve B STG
T049 Steer Valve B Open
T050 Steer Valve C STB
T051 Steer Valve C STG
T052 Steer Valve C Open
T053 Steer Valve D STB
T054 Steer Valve D STG
T055 Steer Valve D Open
T056 Steer Mode Switch Short
T057 Steer Mode Switch Open
T058 Left Turn Output STB
T059 Left Turn Output STG
T060 Left Turn Output Open
T061 Right Turn Output STB
T062 Right Turn Output STG
T063 Right Turn Output Open
T064 Neutral Start STB
T065 Neutral Start STG
T066 Neutral Start Open
T067 Brake Lights STB
T068 Brake Lights STG
T069 Brake Lights Open
T070 Footbrake NC OOR
T071 Footbrake NO OOR
T072 Footbrake Open
T073 Footbrake Short
T074 Reverse Alarm STB
T075 Reverse Alarm STG
T076 Reverse Alarm Open
T077 Ground Speed Sensor OORL
T078 Ground Speed Sensor OORH
T079 Ground Speed Invalid
T080 Secondary Ground Speed Lost
T081 Ground Speed Disagreement
T082 Secondary Ground Speed Invalid
T083 Creep LED STB
T084 Creep LED STG
T085 Creep LED Open
T086 Switch Supply STB
T087 Switch Supply STG
T088 Switch Supply Open
T089 Application Checksum failure
T090 Trans Temp exeeded trans temp warning threshold
T091 Constant Data Checksum failure
T310 CAN data unavailable - Engine percent load at current speed.

Transmission      Not 527-58
T311 CAN data unavailable - Torque converter lockup disable
T312 CAN data unavailable - Engine speed
T730 T solenoid electrical fault
T731 W solenoid electrical fault
T732 U solenoid electrical fault
T733 V solenoid electrical fault
T734 X solenoid electrical fault
T735 Y solenoid electrical fault
T736 LUC solenoid electrical fault
T737 Neutral start electrical fault
T738 Reverse lamp electrical fault
T739 Z solenoid electrical fault
T740 4WD solenoid electrical fault
T741 Driver indicator (transmission warning lamp) electrical fault
T742 ECU buffered speed signal electrical fault
T743 Low oil pressure lamp electrical fault
T744 Kickdown/pressure electrical fault
T745 Transmission ECU status (use FMI = 13 for "No setup file - blank ECU")
T746 Transmission Oil temp is too high
T747 Transmission oil pressure low
T748 Gear selector logical error
T749 Column switch electrical fault
T750 Joystick electrical fault
T751 Hand brake switch fault
T752 Foot brake pressure switch fault
T800 Transmission speed signal open circuit
T801 Engine speed signal open circuit
T900 Transmission speed signal voltage above normal
T901 Engine speed signal voltage above normal
T950 Transmission speed signal voltage below normal
T951 Engine speed signal voltage below normal

Data logger codes
Z000 Errors Logs Erased
Z111 Error Logs Full
Z200 Vehicle Serviced
Назад к содержимому