Code List BOBCAT - Автозапчасти и автоХитрости

Автозапчасти и автоХитрости
Автозапчасти и автоХитрости
Автозапчасти и автоХитрости
Подписывайтесь на наш канал в Telegram и будьте всегда в курсе самых последних сообщений и публикаций с сайта.
Перейти к контенту
Коды неисправностей по спецтехнике BOBCAT

01-16 is not connected air filter
01-17 clogged air filter
02-16 Filter hydraulic / hydrostatic system is not connected
02-17 Filter hydraulic / hydrostatic system is connected
03-09 Low battery voltage
03-10 High Voltage Battery g
03-11 Extremely high voltage battery
03-14 Extremely low battery voltage
03-22 Battery voltage is below the limit
04-09 Low levels of engine oil pressure
04-14 Extremely low levels of engine oil pressure
04-15 Engine oil pressure at the level of the emergency engine shutdown
04-21 Engine oil pressure above the maximum permissible
04-22 Engine oil pressure below the limit
05-09 Low supply pressure in the hydraulic system
05-10 High charge pressure in the hydraulic system
05-11 Extremely high charge pressure in the hydraulic system
05-14 Extremely low supply pressure in the hydraulic system
05-15 charge pressure in the hydraulic system at the level of the emergency engine shutdown
05-21 charge pressure in the hydraulic system above the maximum permissible
05-22 charge pressure in the hydraulic system below the limit
06-10 high engine speeds
06-11 Extremely high engine speed
06-13 No engine speed signal
06-15 Engine speed at the level of the emergency engine shutdown
06-18 Engine speed is out of range
07-10 Heat the oil in the hydraulic system
07-11 Extremely high temperature hydraulic oil
07-15 The oil temperature in the hydraulic system at the level of the emergency engine shutdown
07-21 The oil temperature in the hydraulic system above the maximum allowable
07-22 The oil temperature in the hydraulic system below the limit
08-10 High engine coolant temperature
08-11 Extremely high engine coolant temperature
08-15 Engine coolant temperature at the level of the emergency engine shutdown
08-21 Engine coolant temperature is higher than the maximum permissible
08-22 Engine coolant temperature is below the limit
09-09 Low fuel level
09-21 Fuel level above the maximum permissible
09-22 Fuel level below the limit
10-17 clogged hydraulic filter discharge
11-05 frame sensor security shorted to battery
11-06 frame sensor security shorted to ground
12-21 Signal ShIMkontrollera front ext. hydraulics for the upper limit of the range
12-22 ShIMkontroller front ext. hydraulics for the lower range
12-23 ShIMkontroller front ext. Hydraulic not in the neutral range
13-05 Retaining fuel cutoff solenoid shorted to battery
13-06 Retaining fuel cutoff solenoid shorted to ground
13.7 Open circuit solenoid fuel cutoff
14-02 retracting solenoid fuel cutoff, the erroneous inclusion
14-03 retracting solenoid fuel cutoff, erroneous shutdown
15-02 retracting solenoid lock rods, erroneous inclusion
15-03 retracting solenoid lock rods, erroneous shutdown
16-05 Retaining solenoid lock rods shorted to battery
16-06 Retaining solenoid locking rod is closed to ground
07-16 Break the chain holding the solenoid lock rod
17-05 hydraulic solenoid shut-off valve is closed to battery
17-06 hydraulic solenoid shut-off valve is closed to ground
17-07 Open circuit hydraulic solenoid shut-off valve
18.05 The solenoid slide is closed to battery
18.6 Solenoid spool is closed to ground
18-07 Open circuit solenoid spool
19-02 solenoid positioning bucket erroneous inclusion
19.3 Solenoid bucket positioning, incorrect shutdown
20-02 Solenoid switching speeds erroneous inclusion
20-03 Solenoid switching speeds, erroneous shutdown Glow plugs 
21-02, the erroneous inclusion
21-03 Glow plugs, faulty shutdown Starter 
22-02, the erroneous inclusion Starter 
22-03, erroneous shutdown
23-02 Rear base solenoid erroneous inclusion
23-03 Rear base solenoid erroneous shutdown
24-02 Rear spindle solenoid erroneous inclusion
24-03 Rear spindle solenoid erroneous shutdown
25-02 Rear auxiliary proportional solenoid erroneous inclusion
25-03 Rear auxiliary proportional solenoid, faulty shutdown
2.26 The erroneous inclusion of the front base solenoid
3.26 Erroneous off the front of the base of the solenoid
27-02 erroneous inclusion of the stem of the front solenoid
3.27 Erroneous front off the stem of the solenoid
28-20 Solenoid relief valve, faulty switch
28-30 Solenoid relief valve, faulty shutdown
29-20 Solenoid large supply, faulty switch
29-30 Solenoid large supply, faulty shutdown
30-28 Failure memory controller
31-28 Fault recovery mode (also appears after the software update)
32-04 Advanced Management (ACS) does not communicate with the controller Bobcat
32-23 Calibration required ACS
32-24 Calibrate ACS
32-31 Fault actuator tilt ACS Faulty wiring 
32-32 tilt actuator ACS
32-33 tilt handle the wiring ACS
32-34 ACS tilt actuator is not in the neutral position
32-35 The handle / pedal tilt bucket ACS is not in the neutral position
32-36 Fault actuator lift ACS Faulty wiring 
32-37 actuator lift ACS
32-38 the wiring arm lifting ACS
32-39 actuator lifting ACS not in the neutral position
32-40 The handle / lift pedal bucket ACS is not in the neutral position
32-41 ACS: no connection
32-49 actuator lift ASS closed to ground
32-50 tilt actuator ASS shorted to ground
32-51 actuator lift ASS shorted to battery
32-52 tilt actuator ASS shorted to battery
32-53 Handle / foot boom is closed to ground, ASS
32-54 Handle / foot slope of the boom is closed to ground, ASS
32-55 Handle / foot boom is closed to battery, ACS
32-56 Handle / foot slope of the boom is closed to battery, ACS
32-57 Reduced performance actuator lift ACS
32-58 Reduced performance actuator tilt ACS
32-59 Wrong direction of the actuator lift ACS
32-60 Wrong direction of the actuator lift ACS
32-61 Chain lock handle ACS shorted to ground
32-62 Chain lock handle ACS closed on battery
32-63 Chain lock pedals ACS is closed to ground
32-64 Chain lock pedals ACS closed on battery
32-65 Voltage sensor out of range ACS
32-66 Battery voltage ACS below the limit
32-67 Switch ACS switched during operation
32-68 Error Information Handle boom, ACS
32-70 Chain right arm movements ACS shorted to ground
32-71 Chain right arm movements ACS closed on battery
32-74 X-axis joystick left ACS is out of range
32-75 Power Off unswitched equipment ACS
32-76 Error Information joystick CAN, ACS
32-77 Error Information remote control, ACS
33-23 The main controller (controller Bobcat) is not programmed
34-04 panel with push-button starting the controller does not communicate with Bobcat
35-02 erroneous inclusion of the fan hydraulics
35-03 Mistaken off the fan hydraulics
36-48 connect multiple controllers ACD
37-02 Two-speed auxiliary switch speeds erroneous inclusion
37-03 Two-speed auxiliary switch speeds erroneous inclusion
38-01 Error Information joystick CAN
38-02 Error Information Remote Control
38-04 There is no communication with the controller joystick
38-05 X axis the left stick is not in the neutral position
38-06 X axis right stick is not in the neutral position
38-07 Y-axis of the left joystick is not in neutral
38-08 Y-axis right stick is not in the neutral position
38-09 mode switch control circuit to the battery or to ground
38-10 Calibrate actuator
38-11 lift actuator is not in the neutral position
38-12 tilt actuator is not in the neutral position
38-13 Failure of the actuator lift
38-14 Failure of the actuator tilt
38-15 Wiring Fault speed control right wheel
38-16 Wiring fault for the speed of the left wheel
38-17 Reduced performance actuator tilt
38-18 Reduced performance actuator lift
38-19 X-axis joystick for left upper range
38-20 X-axis right joystick for the upper limit of the range
38-21 Y-axis joystick for left upper range
38-22 Y-axis right joystick for the upper limit of the range
38-23 front right sensor signal controls the upper limit of the range
38-24 front left sensor signal controls the upper limit of the range
38-25 rear right sensor signal controls the upper limit of the range
38-26 rear left sensor signal controls the upper limit of the range
38-27 Signal actuator for lifting the upper range
38-28 Signal actuator for tilting the upper range
38-29 X-axis joystick left for lower range
38-30 X-axis right joystick for the lower range
38-31 Y-axis joystick left for lower range
38-32 Y-axis right joystick for the lower range
38-33 front right sensor signal controls the lower end of the range
38-34 front left sensor signal controls the lower end of the range
38-35 rear right sensor signal controls the lower end of the range
38-36 rear left sensor signal controls the lower end of the range
38-37 Power "1" 5-volt sensor for the lower range
38-38 Power "2" 5-volt sensor for the lower range
38-39 actuator lift is closed to ground / lower boundary of the range
38-40 tilt actuator is closed to ground / signal for the lower range
38-41 Wrong direction of the tilt actuator
38-42 Wrong direction of the actuator lift
38-43 left front solenoid actuator erroneous inclusion
38-44 Solenoid left reverse drive, faulty switch
38-45 right front solenoid actuator erroneous inclusion
38-46 Solenoid right reverse drive, faulty switch
38-47 Front right solenoid control switch faulty
38-48 Front left solenoid control switch faulty
38-49 Rear right solenoid control switch faulty
38-50 Rear left solenoid control off erroneous
38-51 solenoid pressure control system, the erroneous inclusion
38-52 Back-up alarm, the erroneous inclusion
38-53 Solenoid left front drive off false
38-54 Solenoid left reverse drive, faulty shutdown
38-55 right front solenoid drive off false
38-56 Solenoid right reverse drive, faulty shutdown
38-57 Front right solenoid control extension, erroneous shutdown
38-58 Front right solenoid control retraction, erroneous shutdown
38-59 Front left solenoid control extension, erroneous shutdown
38-60 Front left solenoid control retraction, erroneous shutdown
38-61 Rear right solenoid control extension, erroneous shutdown
38-62 Rear right solenoid control retraction, erroneous shutdown
38-63 Rear left solenoid control extension, erroneous shutdown
38-64 Rear left solenoid control retraction, erroneous shutdown
38-65 solenoid pressure control system, faulty shutdown
38-66 Back-up alarm, erroneous shutdown
38-67 No communication from Bobcat controller
38-68 wheel alignment (alignment) not calibrated
38-69 Fault calibration actuators lift and tilt
38-70 Fault recovery mode range
38-71 Battery voltage out of limits
38-72 Pump drive is not calibrated
38-73 Control Mode Switch switched during operation
38-74 Uncontrolled rotation speed of the right wheel
38-75 Uncontrolled rotation speed of the left wheel
38-76 solenoid pressure control system Undercurrent
38-77 Front right solenoid control extension Undercurrent
38-78 Front right solenoid control retraction Undercurrent
38-79 Front left solenoid control extension Undercurrent
38-80 Front left solenoid control retraction Undercurrent
38-81 Rear right solenoid control extension Undercurrent
38-82 Rear right solenoid control retraction Undercurrent
38-83 Rear left solenoid control extension Undercurrent
38-84 Rear left solenoid control retraction Undercurrent
38-85 Power "1" 5-volt sensor for the upper limit of the range
38-86 ° Power "2" 5-volt sensor for the upper limit of the range
38-87 Problem front right steering device for the lower range
38-88 Malfunction of the front left of the steering gear
38-89 Fault rear right of the steering gear Error 
38-90 rear left control
38-91 No speed sensor impulses of the right wheel
38-92 No speed sensor impulses left wheel
38-93 right wheel speed sensor does not respond
38-94 left wheel speed sensor does not respond
38-95 Change of direction in the left wheel speed sensor
38-96 Change of direction in the right wheel speed sensor
38-98 controller in calibration mode drive
38-99 controller in calibration mode wheel position
39-04 Left joystick has no communication with the controller Bobcat
39-05 X-axis is not in the neutral position
39-07 Y-axis is not in the neutral position
39-12 manipulator switch left stick is not in neutral
39-13 is not connected joystick handle left off
39-16 is not connected joystick left off
39-28 Internal fault of the left joystick
39-48 Left joystick, multi-mode
40-04 Right joystick has no communication with the controller Bobcat
40-05 X axis right stick is not in the neutral position
40-07 Y-axis right stick is not in the neutral position
40-12 manipulator switch right joystick is not in neutral
40-13 is not connected right stick handle
40-16 is not connected right stick
40-28 Internal fault of the right joystick
40-48 Right stick, multi-mode
41-09 Low voltage generator
41-10 High Voltage Generator
41-11 Extremely high voltage generator
44-02 Horn, the erroneous inclusion
44-03 Horn, erroneous shutdown
45-02 The right turn signal, the erroneous inclusion
45-03 The right turn signal, erroneous shutdown
46-02 left turn signal, the erroneous inclusion
46-03 left turn signal, erroneous shutdown
47-21 Power 8voltovogo sensor for upper range
47-22 Power 8voltovogo sensor for lower range
48-02 front light switch, faulty switch
48-03 front light switch, faulty shutdown
49-02 Relay rear light erroneous inclusion
49-03 Relay rear light, faulty shutdown
60-21 signal lever back ext. hydraulics for the upper limit of the range
60-22 signal lever back ext. hydraulics for the lower range
60-23 lever rear ext. Hydraulic not in the neutral position
64-02 erroneous inclusion of a power relay
64-03 Mistaken off power relay
73-04 Fault remote control
73-13 Remote control signal is missing
74-72 Fault boot code controller Bobcat
75-01 Error Information joystick CAN
75-04 There is no communication with the controller drive
75-05 X axis the left stick is not in the neutral position
75-07 Y-axis of the left joystick is not in neutral
75-08 Y-axis right stick is not in the neutral position
75-09 mode switch ISO / H circuit to battery or to ground
75-13 jammed angle sensor right front wheel
75-14 jammed angle sensor left front wheel
75-15 jammed angle sensor right rear wheel
75-16 jammed angle sensor left rear wheel
75-17 left inclined plate is not in the neutral position
75-18 right oblique plate is not in the neutral position
75-19 X-axis joystick for left upper range
75-21 Y-axis joystick for left upper range
75-22 Y-axis right joystick for the upper limit of the range
75-23 Signal angle sensor right front wheel of the upper limit of the range
75-24 Signal angle sensor left front wheel of the upper limit of the range
75-25 Signal angle sensor right rear wheel for the upper limit of the range
75-26 Signal angle sensor left rear wheel of the upper limit of the range
75-27 Offset left oblique plate
75-28 Offset right oblique plate
75-29 X-axis joystick left for lower range
75-31 Y-axis joystick left for lower range
75-32 Y-axis right joystick for the lower range
75-33 Signal angle sensor right front wheel of the lower boundary of the range
75-34 Signal angle sensor left front wheel of the lower boundary of the range
75-35 Signal angle sensor right rear wheel of the lower boundary of the range
75-36 Signal angle sensor left rear wheel of the lower boundary of the range
75-37 Power "1" 5-volt sensor for the lower range
75-38 Sensor supply 2 for the lower range
75-39 Sensor Signal Left inclined plate for the top end of the range
75-40 Sensor Signal Left inclined plate for bottom of the range
75-41 Sensor Signal Right inclined plate for the top end of the range
75-42 Sensor Signal Right inclined plate for bottom of the range
75-43 left front solenoid actuator erroneous inclusion
75-44 Solenoid left reverse drive, faulty switch
75-45 right front solenoid actuator erroneous inclusion
75-46 Solenoid right reverse drive, faulty switch
75-47 Front right solenoid control extension shorted to battery
75-48 Front left solenoid control extension shorted to battery
75-49 Rear right solenoid control extension shorted to battery
75-50 Rear left solenoid control extension shorted to battery
75-51 solenoid pressure control system is closed to battery
75-52 Back-up alarm, the erroneous inclusion
75-53 Solenoid left front drive off false
75-54 Solenoid left reverse drive, faulty shutdown
75-55 right front solenoid drive off false
75-56 Solenoid right reverse drive, faulty shutdown
75-57 Front right solenoid control extension shorted to ground
75-58 Front right solenoid control retraction shorted to ground
75-59 Front left solenoid control extension shorted to ground
75-60 Front left solenoid control retraction shorted to ground
75-61 Rear right solenoid control extension shorted to ground
75-62 Rear right solenoid control retraction shorted to ground
75-63 Rear left solenoid control extension shorted to ground
75-64 Rear left solenoid control retraction shorted to ground
75-65 solenoid pressure control system is closed to ground
75-66 Back-up alarm, erroneous shutdown
75-67 No communication from Bobcat controller
75-68 angle sensors are not calibrated
75-69 Battery voltage is above the maximum permissible
75-70 Fault recovery mode (also appears after the software update)
75-71 Battery voltage is below the limit
75-72 Pump drive is not calibrated
75-73 mode switch ISO / H switched during operation
75-74 Uncontrolled rotation speed of the right wheel
75-75 Uncontrolled rotation speed of the left wheel
75-76 There are no posts from the controller ACS
75-77 speed sensor signal of the left wheel of the upper limit of the range
75-78 speed sensor signal of the right wheel of the top of the range
75-79 speed sensor signal of the left wheel of the lower boundary of the range
75-80 speed sensor signal of the right wheel of the bottom of the range
75-81 Front right solenoid control retraction shorted to battery
75-82 Front left solenoid control retraction shorted to battery
75-83 Rear right solenoid control retraction shorted to battery
75-84 Rear left solenoid control retraction shorted to battery
75-85 Power "1" 5-volt sensor for the upper limit of the range
75-86 Sensor supply 2 for the upper limit
75-88 controller in programming mode
75-91 Changing the polarity of the left oblique sensor plate
75-92 Changing the polarity of the sensor right oblique plate
75-93 right wheel speed sensor does not respond
75-94 left wheel speed sensor does not respond
75-95 Change of direction in the left wheel speed sensor
75-96 Change of direction in the right wheel speed sensor
75-98 controller in calibration mode
76-73 left panel, the error of the receiver
77-48 Ignition Switch, multi-mode
78-74 Door / locking the lock is opened / closed
80-02 ACD, output «A», the erroneous inclusion
80-03 ACD, output «A», erroneous shutdown
81-02 ACD, exit «B», the erroneous inclusion
81-03 ACD, exit «B», erroneous shutdown
82-02 ACD, output «C», the erroneous inclusion
82-03 ACD, output «C», erroneous shutdown
83-02 ACD, exit «D», the erroneous inclusion
83-03 ACD, exit «D», erroneous shutdown
84-02 ACD, exit «E», the erroneous inclusion
84-03 ACD, exit «E», erroneous shutdown
85-02 ACD (controller attachments), exit «F», the erroneous inclusion
85-03 ACD, exit «F», erroneous shutdown
86-02 ACD, exit «G», the erroneous inclusion
86-03 ACD, exit «G», erroneous shutdown
87-02 ACD, exit «H», the erroneous inclusion
87-03 ACD, exit «H», erroneous shutdown
90-02 Service Output «C», the erroneous inclusion
90-03 Service Output «C», erroneous off wheels
91-02 Service Output «D», the erroneous inclusion
91-03 Service Output «D», erroneous shutdown
92-02 Service Output "E", the erroneous inclusion
92-03 Service Output "E" erroneous shutdown
93-02 Service Output «F», the erroneous inclusion
93-03 Service Output «F», erroneous shutdown
Назад к содержимому