Коды неисправностей Tier 3 JCB - Автозапчасти и автоХитрости

Автозапчасти и автоХитрости
Автозапчасти и автоХитрости
Автозапчасти и автоХитрости
Подписывайтесь на наш канал в Telegram и будьте всегда в курсе самых последних сообщений и публикаций с сайта.
Перейти к контенту
 См. также:
Коды неисправностей двигателя Tier 3 JCB

DTC          Error Title           Description
P0087 Fuel rail pressure is too low (Fuel leak).
Actual rail pressure < Minimum target rail pressure at actual rail pressure is 15MPa or more.

P0088 Common rail pressure (1st stage) Rail pressure is over 185MPa P0088 Common rail pressure (2nd stage).
Common rail pressure failure (1st. Stage) is occurred and the rail pressure is over 190MPa.

P0089 Common rail pressure (excessive pressure for pump).
DUTY for SCV is 40% or more. Or Actual rail press -Target rail press≧40MPa~ then target fuel flow is 90mm3/st or less.

P0090 Fuel pressure regulator control circuit.
SCV driving current > 2400mA or 50mA < SCV driving current, or Target current - Actual current ≧1000 mA.

P0107 Air pressure sensor (low voltage) The voltage of air pressure temperature sensor falls below 0.099V.

P0108 Air pressure sensor (high voltage) The voltage of air pressure temperature sensor exceeds 4.85V. 

P0112 Intake air temperature circuit(low voltage) The voltage of intake temperature sensor falls below 0.099V. 

P0113 Intake air temperature circuit(high voltage) The voltage of intake temperature sensor exceeds 4.85V. 

P0117 Engine coolant temperature circuit (low voltage) The voltage of water temperature sensor falls below 0.099V. 

P0118 Engine coolant temperature circuit (high voltage) The voltage of water temperature sensor exceeds 4.85V. 

P0182 Fuel temperature sensor circuit(low voltage) The voltage of fuel temperature sensor falls below 0.099V. 

P0183 Fuel temperature sensor circuit (high voltage) The voltage of fuel temperature sensor exceeds 4.85V. 

P0192 Fuel rail pressure sensor circuit (low voltage) The voltage of common rail pressure sensor falls below 0.7V. 

P0193 Fuel rail pressure sensor circuit (high voltage) The voltage of common rail pressure sensor exceeds 4.5V. 

P0201 Injector circuit cylinder 1 Input signal at inj. No.1 is not active P0202 Injector circuit cylinder 2 Input signal at inj. No.2 is not active .

P0203 Injector circuit cylinder 3 Input signal at inj. No.3 is not active. 

P0204 Injector circuit cylinder 4 Input signal at inj. No.4 is not active. 

P0205 Injector circuit cylinder 5 Input signal at inj. No.5 is not active. 

P0206 Injector circuit cylinder 6 Input signal at inj. No.6 is not active. 

P0219 Over run Engine speed exceeds 2300 rpm (In case of 6HK1). 

P0237 Boost pressure sensor (low voltage) The voltage of boost pressure sensor falls below 0.099V. 

P0238 Boost pressure sensor (high voltage) The voltage of boost pressure sensor exceeds 4.85V. 

P0335 Crank sensor (no signal) Cam signal is active but Crank signal is not active. 

P0336 Crank sensor (signal error) Discrepancy in base crank signal pulse rate. 

P0340 Cam sensor (no signal) Crank signal is active but Cam signal is not active. 

P0341 Cam sensor (signal error) Discrepancy in base Cam signal pulse rate. 

P0380 Glow relay.
No signal of Glow Relay Monitor against the instruction of Glow Relay Driving at the IGKEY power voltage is 16V-32V.

P0381 Glow lamp No signal of Glow Lamp monitoring against instruction for lighting glow lamp. 

P0487 EGR positioning signal error(brush less spec.) Output signal of EGR Valve position sensor is out of the range. 

P0488 EGR valve control failure The rate difference between target valve lift and the actual position is 20% or more. 

P0522 Engine oil pressure sensor (Low voltage irregular) The oil pressure sensor falls below 0.099V. 

P0523 Engine oil pressure sensor (High voltage irregular) The oil pressure sensor exceeds 4.85V. 

P0601 ROM ROM error P0603 EEPROM EEPROM error P0606 CPU Sub CPU detected the failure of main CPU. 

P0606 IC for CPU detection RUN-SUB pulse doesn't change for 20msec or more. 

P0611 ECM Charge circuit 1 (Low Voltage) The voltage in ECU charge circuit 1 is low. 

P0612 ECM Charge circuit 2 (Low Voltage) The voltage in ECU charge circuit 2 is low. 

P1093 Fuel rail pressure is low during power enrichment. (Fuel leak) At fuel rail pressure Qty. = 
8000mm3 / st or more, Target rail pressure - Actual rail pressure >15MPa.

P1095 Pressure limiter open Pressure limiter is opened. 

P1112 Boost temperature sensor (Low voltage irregular) The voltage of boost temperature sensor falls below 0.099V. 

P1113 Boost temperature sensor (High voltage irregular).
The voltage of boost temperature sensor exceeds 4.85V at water temperature exceeds 50℃ or more, or more than 5 minutes have past since Key On.

P1173 Over heat Water temperature exceeds 120℃ at engine running. 

P1261 Injector circuit group 1 No monitoring input signal from Inj.1 & 4 (4 cyl) or 1 & 2 & 3 (6 cyl) P1262 Injector circuit group 2 No monitoring input signal from Inj. 2 & 3 (4 cyl) or 4 & 5 & 6 (6 cyl) P1271 Accel sensor circuit 1-2 correlation The difference of accelsensor open-rate between No.1 and No.2 is more than 45%. 

P1272 Accel sensor circuit 2-3 correlation The difference of accelsensor open-rate between No.2 and No.3 is more than 45%. 

P1273 Accel sensor circuit 1-3 correlation The difference of accelsensor open-rate between No.1 and No.3 is more than 45%. 

P1277 Accel sensor circuit 1(low input) The voltage of accel sensor No.1 falls below 0.199V. 

P1278 Accel sensor circuit 1(high input) The voltage of accel sensor No.1exceeds 4.9V P1282 Accel sensor circuit 2(low input) The voltage of accel sensor No.2 falls below 0.199V. 

P1283 Accel sensor circuit 2(high input) The voltage of accel sensor No.2 exceeds 4.9V. 

P1287 Accel sensor circuit 3(low input) The voltage of accel sensor No.3 falls below 0.199V. 

P1288 Accel sensor circuit 3(high input) The voltage of accel sensor No.3 exceeds 4.9V. 

P1293 Fuel filter clogging sensor fault( Low voltage) The voltage of boost pressure sensor falls below 0.099V. 

P1294 Fuel filter clogging sensor fault( High voltage) The voltage of boost pressure sensor exceeds 4.85V. 

P1345 Cam&Crank sensor pulse phase (Phase difference) Difference Cam pulse is beside the Crank gap position Output of Main relay coils : On, and the voltage of main relay line is 1V or less.
Output of Main relay coils : Off and the voltage of main relay line is 18V or more.

P1630 A/D conversion A/D does not convert. P1631 5 Volt reference 1 circuit.
IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.

P1632 5 Volt reference 2 circuit.
IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.

P1633 5 Volt reference 3 circuit.
IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.

P1634 5 Volt reference 4 circuit.
IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.

P1635 5 Volt reference 5 circuit.
IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range is from 16V to 32V.

U2104 CAN Bus Bus off detection. 

U2106 CAN Time out Lost communication for a set hours.
Назад к содержимому